With this items you can assemble all of our digital component easily below your railroad layout.
Accessories for products
from our Digital-Professional-Series.
For installation of decoders below the railroad layout:
| We supply under the order code of
MON-SET
a suitable installation material
for the components of the Digital-Professional-Series! Each set consist
of four plastic spacers (length 5mm) and four matching wood screws (13mm length)
and can be ordered for only € 0,90. With this items you can assemble all of our digital component easily below your railroad layout. |
|
We supply under the order code LDT-01 a practical and elegant case suitable for the turnout decoder S-DEC-4, the switch decoder SA-DEC-4, the light-signal decoder LS-DEC-DB, LS-DEC-DR, LS-DEC-SBB, LS-DEC-NS, LS-DEC-NMBS and LS-DEC-ÖBB, the train influence module ZBM, the feedback module RM-88-N, RM-88-N-O, RM-DEC-88, RM-DEC-88-O, RS-16-O, the high speed interface HSI-88(-USB), the WatchDog-decoder WD-DEC, the traindetect TD-88, the transponder reader COL-10 , the data switch DSW-88, the digitalbooster DB-2, the track occupancy detector GBM-8, the keycommander KeyCom, the reverse-loop module KSM-SG and the Turntable-decoder TT-DEC.
The case consists of a lower and a upper cover. The printed circuit board shall be placed into the lower case. The upper case can be easily closed over the pc-board by snap locks. The connection clamps and the operating devices will be free accessible. Dimensions: (length x width x height) 93 x 80 x 32mm.
Each Case LDT-01 comes with a detailed
installation instruction.
The case LDT-01 can be ordered for only € 4,10.
|
|
|
Under the order code LDT-02 we supply a practical and elegant case suitable for the DigitalBooster DB-4, and the Feedback Module RM-GB-8-N.
The case consists of a lower and a upper cover. The printed circuit board shall be placed into the lower case. The upper case can be easily closed over the pc-board by snap locks. The connection clamps and the operating devices will be free accessible. Dimensions: (length x width x height) 116 x 100 x 32mm.
Each Case LDT-02 comes with a
detailed installation instruction. There
are labels for all relevant LDT-Components included for cutting out and sticking
them onto the case for identification.
The case LDT-02 (Part-No.: 000134) can be ordered for only € 5,10.
|
|
|
Splash-water protected housing for the turnout decoder 1-DEC-DC:
If you require a suitable splash-water protected housing for our 4-fold turnout decoder 1-DEC-DC for your outdoor application we can recommend the 120x80x57mm sized housing out of the Euromas-Series of company BOPLA.
We can supply this housing under the order code G-1-DEC for € 15,90 together with a splash-water protected cable joint.
Extended connection cable for the s88-feedback bus:
We supply under the order code Kabel s88 0,5m, Kabel s88 1m and Kabel s88 2m a 0,5 meter, 1 meter respectively 2 meter long cable for s88-standard connections for the s88-feedback bus equipped with 2 original s88-plugs. With this connection cables you can connect the feedback module RM-88-N, RM-88-N-O and RM-GB-8-N or s88 standard module from Märklin or other suppliers directly together or to the digital central unit or interface at a distance of 0,5m, 1m respectively 2 meters.
If you use the attached pin-bar you can extend
the s88-connection of the feedback module RM-DEC-88, RM-DEC-88-O and
RM-GB-8 by 0,5m, 1m respectively by 2 meters.
The cable
s88 0,5m, cable s88 1m respectively cable s88 2m is
a round, interference protected, twisted s88-standard bus cable.
|
|
The Kabel s88 0,5m is available for only € 5,50. |
|
|
|
|
The Kabel s88 1m is available for only € 7,50. |
|
|
|
|
|
The Kabel s88 2m is available for only € 9,50. |
|
|
|
Each Kabel s88 will be supplied with a detailed Operating Instruction.
Connection cable for
s88-connections according to
:
Under the order code Kabel Patch 0,5m, Kabel Patch 1m,
Kabel Patch 2m and Kabel Patch 3m are cables with 2 RJ-45 plugs
at a length of 0,5m, 1m,
2m or. 3m for the s88-connections according to
available.
With this cable you can connect the feedback module RM-88-N,
RM-88-N-O and RM-GB-8-N between each other or on a distance of 0,5m, 1m,
2m or 3m.
Kabel Patch 0,5m € 2,50
Kabel Patch 1m € 3,40
Kabel Patch 2m € 4,80
Kabel Patch 3m € 6,80
5-poles booster bus cable for digital control units and boosters:
5-poles booster bus cable with twisted wires and therefore interference protected for the connection of digital control units (e.g. Control Unit, Intellibox, TWIN-CENTER) with boosters (e.g. 6015 / 6017, Power 3, TWIN-BOOSTER, DB-2, DB-4) and for connecting boosters to each other.
Each DigitalBooster DB-2 will be supplied with oneKabel Booster 1m.
|
|
|
|
The Kabel Booster can not only connect the Booster DB-2 and DB-4 together or with the different digital central units. Also the Märklin Control Unit can be connected to the Märklin Booster 6015 (top) or 6017 (bottom) e.g. via the Kabel Booster 1m.
Under the order code Kabel Booster 1m (Part-No.: 00123) you can purchase the cable of 100cm length for only € 6,90.
Roco / Fleischmann Booster bus-cable:
Booster bus cable with Western-Plugs RJ10 for the connection of the DigitalBooster DB-4 via the Roco-Booster bus with Roco 10761/10764, Fleischmann 680801 and multiZENTRALEpro and with further Digital Booster DB-4.
Under the order code Kabel Roco 1m (Part-No.: 000136) you can purchase the cable of 100cm length for only € 6,90.
Connection cable for Light-Display and Light-Power Module:
If you do not want to connect the Light-Display or Light-Power Modules of the PC-Light Control Light@Night directly to each other but intend to assemble those at a larger distance, you can use the cable Kabel L@N 0,5m with a total length of 0,5 meters, the cable Kabel L@N 1m with a total length of 1 meters or the cable Kabel L@N 2m with a total length of 2 meters.
Each Kabel
Light@Night
will be supplied with a detailed
Operating Instruction.
You can purchase the cable Kabel L@N
0,5m
for only € 5,50,
the cable Kabel
L@N 1m
for only € 7,50 and the cable Kabel
L@N 2m for only €
9,50
Disturbance caused by turnouts with integrated end switches:
Turnout drives with integrated end switch produces considerable electromagnetic interferences. Our decoder QS-DEC-II and S-DEC-4 used for these drives are normally free from influence of such interferences. Nevertheless in case it will come to some interferences you should first check the installation of the turnout cables. Those should not turn around the decoder or cross close up directly across the decoder. Install the cables directly straight away from the clamps of the decoder. If it is not possible to change the installation and interferences will occur you should apply 5 to 10 ferrite pearls onto the common connection of each turnout drive (center connection of each output). Take care that the ferrite pearls are assembled close to the drives to prevent that interferences can spread over the connection wires.
Under the order code FP you can purchase from us 100 suitable ferrite pearls for € 4,09.
© 2010 by LDT
