DSW-88-N
DSW-88-N
Data switch for the s88-feedback bus
from the Digital-Professional-Series !
The data switch DSW-88-N
acts as a Y-cable which can divide the s88-bus.
The below shown cable connects the module to the command station and the two
above s88-cables
are the two new s88-feedback lines, one to the right and one to the left side.
Normally the s88-feedback bus expects all connected feedback modules behind each others in one line. The data switch DSW-88-N provides the possibility to split the s88-feedback output!
The data switch DSW-88-N provides in addition three
6-poles pin bars for the s88 standard connection and as well three
RJ-45 sockets for a bus connection according to
.
For example: Your command station has been placed into the middle of the model railroad layout you do not need anymore to install a long feedback ring. You can now easily split the output after the data switch DSW-88-N for a separate left and right feedback line.
Is the data switch DSW-88-N connected directly to the command station (here Intellibox) is it possible to build two feedback lines for left- and right-hand installation below the layout. If you require another splitting you can just insert one more data switch DSW-88-N into the line.
The data switch
DSW-88-N is applicable on all installation where the s88-bus is used for the feedback
No additional power supply is required
for the data switch DSW-88-N.
The feedback informations will be transfered
through the data switch without any delay.
Each reading of feedback information
started by the command station will report the information of all connected
feedback modules to the central unit. First reading will be the information of
the left line. Following the data switch will change to the right
feedback line for transfer of those informations.
The data switch DSW-88-N is
compatible with all s88-feedback modules available on the market.
LDT-components from the
Digital-Professional-Series can easily be used on any digital model
railway layout. The finished module in a case comes with
a 24 month warranty.
Sample Connections for the
data switch DSW-88-N can be found
here.
Each data switch DSW-88-N will
be supplied with a detailed
operating- / assembly instruction.
The data switch DSW-88-N is available
as a kit or as checked
finished module in a case:| kit (-B) |
finished module in a case (-G) |
|
| DSW-88-N | € 32,50 | € 49,90 |
DSW-88-N-B
(Part-No. 040111): Data switch for the s88-feedback bus
as a kit. DSW-88-N-G
(Part-No. 040113): Data switch for the s88-feedback bus as a
finished module
in a case.Available ex warehouse.
To assure a good connection:
s88-Bus Cable!
a
blue screened patch cable with RJ-45 plugs at four different
length of 0,5 to 3m.
.|
s88-standard connection with 2 original s88-plugs,
gray cable, twisted, round. Plus pin bar for bus extension. |
|
| Kabel s88 0,5m | € 5,50 |
| Kabel s88 1m | € 7,50 |
| Kabel s88 2m | € 9,50 |
|
s88-connection according to
with
2
RJ-45 plugs, blue cable, screened. |
|
| Kabel Patch 0,5m | € 2,50 |
| Kabel Patch 1m | € 3,40 |
| Kabel Patch 2m | € 4,80 |
| Kabel Patch 3m | € 6,80 |
Kabel s88 0,5m
(Part No. 000102): With original s88-plugs, gray cable, twisted,
round.
Kabel s88 1m (Part
No. 000106):
With original s88-plugs, gray cable, twisted, round.
Kabel s88 2m (Part
No. 000101):
With original s88-plugs, gray cable, twisted, round. Kabel Patch 0,5m
(Part No. 000130): With RJ-45 plugs, blue, screened. Kabel Patch 1m
(Part No. 000131): With RJ-45 plugs, blue, screened. Kabel Patch 2m
(Part No. 000132): With RJ-45 plugs, blue, screened.
Kabel Patch 3m (Part
No.
000133):
With RJ-45 plugs, blue, screened.Available ex warehouse.
Subject to technical
changes and errors.
Märklin und Arnold are registered trade marks.
© 2012 by LDT