TT-DEC-R

TurnTable-Decoder for the Roco H0 Turntable 42615

For the digital control of Roco H0 Turntable 42615! Suitable for the digital formats Märklin-Motorola and DCC.

tt-dec-r_11_01.jpg

Features of the TT-DEC-R

The TurnTable-Decoder TT-DEC-R is suitable for the digital control of the Roco H0 Turntable 42615.

The Roco H0 turntable 42615 can be equipped with 4 up to 40 track connections.
Non-aligned opposite track connection can be assembled at a min. of 4,5 degree offset.

The command-set of the TT-DEC-R is compatible to the Märklin Turntable electronic 7686. Therefore is a very simple control via any Digital Command Station and Model railway software possible, which supports the Märklin turntable electronic 7686 with a turntable graphic.

The digital format (Märklin-Motorola or DCC) and the location of the track connections are easily programmable via any digital command station which is able to switch turnouts or via a model railway software which supports the Märklin turntable electronic 7686. Any track connection of the turntable can be programmed as track 1 (reference track).

The TT-DEC-R permits the step by step rotation to the right- or left side, the direct connection of pre-selected tracks and turning the movement direction of the turntable by 180 degree.

The rotation speed of the turntable can be individually adjusted via a potentiometer. The motor of the turntable receives a stabilized direct voltage for a steady turning movement of the bridge track.

The plug of the 8-poles flat ribbon cable of the Roco H0 turntable 42615 shall be plugged directly onto the pin-plug bar of the TT-DEC-R.

The bridge track receives thecorrect polarity from an integrated switch-over relay. Therefore is no additional reverse loop module for the bridge track required.

If the turntable will be in the lined-up track position this can be reported to the model railway software via the feedback output of the Turntable-Decoder TT-DEC-R.

There no alteration required on the Roco H0 Turntable 42615. There are only two small electrical adaption necessary. After completion of the electrical adaption is it not anymore possible to control the Roco Turntable 42615 by use of the Roco manual control unit.

The finished module in a case comes with 24 month warranty.
Each TurnTable-Decoder TT-DEC-R will be supplied with a detailed operating-/ assembly instruction. Those instructions can be found within the next section.

The TT-DEC-R is available as a kit (-B) or as checked finished module in a case (-G). Suitable assembly material for the kit is available under Accessories.

Downloads

Instructions regarding this article can be found here: Downloads TT-DEC-R.
Instructions for all LDT-Components can be found here: Overview Downloads.

Sample-Connections

Sample-connections regarding this article can be found here: Sample-Connections TT-DEC-R.
Sample-connections for all LDT-Components can be found here: Overview Sample-Connections.

Add to Wish List / Prices

Attention: Products can only be added to the Wish List, if you are registered as customer at the LDT WebShop or if you are initially registered by interest of our products.


Add to Wish List:TT-DEC-R-B (Part-No.: 010511): TurnTable-Decoder as a kit (82,90 €*).
Add to Wish List:TT-DEC-R-G (Part-No.: 010513): TurnTable-Decoder as a finished module in a case (124,90 €*).

* All prices incl. VAT, plus Shipping.

Subject to technical changes and errors.
© 2014 by LDT

 
Recent changes RSS feed Creative Commons License Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki Design by Chirripó